565net必赢(中国)股份有限公司

您现在的位置:必赢565net官网    源拓产品 > 光模块 > SFP+光模块 > SFP+-10GBASE-T 10G电口模块
SFP+光模块

SFP+-10GBASE-T 10G电口模块

型号: SFP+-10GBASE-T


10GBASE-T Copper SFP+ Transceiver 10G电口模块具有性能高、可靠性强等特点,主要用来在超六类或七类铜缆布线系统中实现10G以太网传输,它的传输距离可以达到30 m。 此外其端口既可以支持屏蔽双绞线,又能支持非屏蔽双绞线

产品描述 技术参数 应用方案 相关下载 相关产品

 10G电口模块特点

 

l市场大多数数据中心内设备间的链路距离在10 m到100 m之间,使用10GBASE-T SFP+电口光模块能弥补SFP+高速线缆传输距离的不足。

l10GBASE-T SFP+电口模块采用RJ45接口,和超六类或七类网线一起使用,而铜缆布线的成本要比光缆布线的低。

l在成本上,10GBASE-T SFP+电口模块可以直接用在现有的铜缆布线系统中实现10G传输,而使用SFP+光模块则需要用光缆进行布线,这会增加部署成本。如果想要在现有铜缆布线系统中使用SFP+光模块,则需要增加以太网交换机或光电转换器等设备

 

 PRODUCT FEATURES

 

l  Support 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T

l  Hot-pluggable SFP footprint

l  Compact RJ-45 connector assembly

l  RoHS compliant and lead-free 

l Single +3.3V power supply 

l 10 Gigabit Ethernet over Cat 6a cable

lAmbient Operating temperature: 0°C to +60°C 

 

 PRODUCT DESCRIPTION

 

SFP+-10GBASE-T Copper Small Form Pluggable (SFP) transceivers are based on the SFP Multi Source Agreement (MSA) . They are compatible with the 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T standards as specified in IEEE Std 802.3 . SFP+-10GBASE-T uses the SFP's RX_LOS pin for link indication. If pull up SFP's TX_DISABLE pin,  PHY IC be reset.

  +3.3V Volt Electrical Power Interface

 

The SFP+-10GBASE-T has an input voltage range of 3.3 V +/- 5%. The 4V maximum voltage is not allowed for continuous operation.

+3.3 Volt Electrical Power

Interface

Parameter

Symbol

Min

Typ

Max

unit

Notes/Conditions

Supply Current

Is

 

700

900

mA

3.0W max power over

full range of voltage

and temperature.

See caution note below

Input Voltage

 Vcc

3.13

3.3

3.47

V

Referenced to GND

Maximum Voltage

Vmax

 

 

4

V

 

Surge Current

Isurge

 

TBD

 

mA

Hot plug above steady state

current.  See caution note

below

  

Caution: Power consumption and surge current are higher than the specified values in the SFP MSA 

 

Outline drawing (mm)

标签:   SFP+光模块

 Low-Speed Signals

 

MOD_DEF(1)  (SCL)  and  MOD_DEF(2)  (SDA),  are  open  drain  CMOS  signals  (see section VII, "Serial Communication Protocol").   Both MOD_DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc

  

Low-Speed Signals,  Electronic Characteristics

Parameter

Symbol

Min

Max

unit

Notes/Conditions

SFP Output LOW

VOL

0

0.5

V

 

4.7k to 10k pull-up to host_Vcc,

measured at host side of connector

SFP Output HIGH

VOH

host_Vcc -0.5

host_Vcc + 0.3

V

 

4.7k to 10k pull-up to host_Vcc,

measured at host side of connector

SFP Input LOW

VIL

0

0.8

V

4.7k to 10k pull-up to Vcc,

measured at SFP side of connector

 

SFP Input HIGH

VIH

2

Vcc + 0.3

V

4.7k to 10k pull-up to Vcc,

measured at SFP side of connector

 

 

  High-Speed Electrical Interface

 

All high-speed signals are AC-coupled internally.

 

High-Speed Electrical Interface,  Transmission Line-SFP

Parameter

Symbol

Min

Typ

Max

unit

Notes/Conditions

Line Frequency

fL

 

125

 

MHz

5-level encoding, per

IEEE 802.3

Tx Output Impedance

Zout,TX

 

100

 

Ohm

Differential, for all

frequencies between

1MHz and 125MHz

Rx Input Impedance

Zin,RX

 

100

 

Ohm

Differential, for all

frequencies between

1MHz and 125MHz

 

 

High-Speed Electrical Interface,  Host-SFP

Parameter

Symbol

Min

Typ

Max

unit

Notes/Conditions

Single ended data input

swing

Vinsing

250

 

1200

mV

 

Single ended

Single ended data output

swing

Voutsing

350

 

800

mV

Single ended

Rise/Fall Time

Tr,Tf

 

175

 

psec

20%-80%

Tx Input Impedance

Zin

 

50

 

Ohm

Single ended

Rx Output Impedance

Zout

 

50

 

Ohm

Single ended

 

有关详细信息,请在“相关下载”中查看数据表

 

Baidu
sogou